Appendix 1 Table 1 Inner Ring of 0 Grade Telerance
d mm | Δdmp | Vdp | Vdmp | Kia | ΔBs | VBs | ||||||
Diameter Series | ||||||||||||
9 | 0,1 | 2,3,4 | ALL | normal | revise | |||||||
over | incl. | high | low | max. | max. | max. | high | low | max. | |||
0.6 | 2.5 | 0 | -8 | 10 | 8 | 6 | 6 | 10 | 0 | -40 | - | 12 |
2.5 | 10 | 0 | -8 | 10 | 8 | 6 | 6 | 10 | 0 | -120 | -250 | 15 |
10 | 18 | 0 | -8 | 10 | 8 | 6 | 6 | 10 | 0 | -120 | -250 | 20 |
18 | 30 | 0 | -10 | 13 | 10 | 8 | 8 | 13 | 0 | -120 | -250 | 20 |
30 | 50 | 0 | -12 | 15 | 12 | 9 | 9 | 15 | 0 | -120 | -250 | 20 |
Note:
1)Including 0.6.
2)Diameter series 7 and 8,no regular cost.
3)Indicating the single linternal ring of the bearing to be uesd in pair or group duing
Table 2 Out Ring of 0 Grade Telerance
D mm | Δdmp | Vdp | Vdmp | Kea | ΔCs ΔCis | VCs VCis | ||||||
Open Bearings | Copped Bearings | |||||||||||
Diameter Series | ||||||||||||
9 | 0,1 | 2,3,4 | 2,3,4 | |||||||||
over | incl. | high | low | max. | max. | max. | high | low | max. | |||
2.5 | 6 | 0 | -8 | 10 | 8 | 6 | 10 | 6 | 15 | Identical to ΔBs and VBs of inner ring of same bearing | ||
6 | 18 | 0 | -8 | 10 | 8 | 6 | 10 | 6 | 15 | |||
18 | 30 | 0 | -9 | 12 | 9 | 7 | 12 | 7 | 15 | |||
30 | 50 | 0 | -11 | 14 | 11 | 8 | 16 | 8 | 20 | |||
50 | 80 | 0 | -13 | 16 | 13 | 10 | 20 | 10 | 25 |
Note:1)Including 2.5.
2)Diameter series 7 and 8,no regular cost.
3)Diameter series 9、0 and 8,no regular cost.
4)Suitable for inside and outside brake ring before installation or after discharge.
5)Only suitable for groove type ball bearing.
Appendix 2 Table3 Inner Ring of 6 Grade Telerance
d mm | Δdmp | Vdp | Vdmp | Kia | ΔBs | VBs | ||||||
Diameter Series | ||||||||||||
9 | 0,1 | 2,3,4 | ALL | normal | revise | |||||||
over | incl. | high | low | max. | max. | max. | high | low | max. | |||
0.6 | 2.5 | 0 | -7 | 9 | 7 | 5 | 5 | 5 | 0 | -40 | - | 12 |
2.5 | 10 | 0 | -7 | 9 | 7 | 5 | 5 | 6 | 0 | -120 | -250 | 15 |
10 | 18 | 0 | -7 | 9 | 7 | 5 | 5 | 7 | 0 | -120 | -250 | 20 |
18 | 30 | 0 | -8 | 10 | 8 | 6 | 6 | 8 | 0 | -120 | -250 | 20 |
30 | 50 | 0 | -10 | 13 | 10 | 8 | 8 | 10 | 0 | -120 | -250 | 20 |
50 | 80 | 0 | -12 | 15 | 15 | 9 | 9 | 10 | 0 | -150 | -380 | 25 |
Note:
1)Including 0.6.
2)Diameter series 7 and 8,no regular cost.
3)Indicating the single linternal ring of the bearing to be uesd in pair or group duing installation.
Table4 Out Ring of 6 Grade Telerance
D mm | Δdmp | Vdp | Vdmp | Kea | ΔCs ΔCis | VCs VCis | ||||||
Open Bearings | Copped Bearings | |||||||||||
Diameter Series | ||||||||||||
9 | 0,1 | 2,3,4 | 2,3,4 | |||||||||
over | incl. | high | low | max. | max. | max. | high | low | max. | |||
2.5 | 6 | 0 | -7 | 9 | 7 | 5 | 9 | 5 | 8 | Identical to ΔBs and VBs of inner ring of same bearing | ||
6 | 18 | 0 | -7 | 9 | 7 | 5 | 9 | 5 | 8 | |||
18 | 30 | 0 | -8 | 10 | 8 | 6 | 10 | 6 | 9 | |||
30 | 50 | 0 | -9 | 11 | 9 | 7 | 13 | 7 | 10 | |||
50 | 80 | 0 | -11 | 14 | 11 | 8 | 16 | 8 | 13 |
Note:
1)Including 2.5.
2)Diameter series 7 and 8,no regular cost.
3)Diameter series 9、0 and 8,no regular cost.
4)Suitable for inside and outside brake ring before installation or after discharge.
5)Only suitable for groove type ball bearing.
Appendix 3 Table 5 Inner Ring of 5 Grade Telerance
d mm | Δdmp | Vdp | Vdmp | Kia | Sd | Sia | ΔBs | VBs | |||||
Diameter Series | |||||||||||||
9 | 0,1,2,3,4 | ALL | normal | revise | |||||||||
over | incl. | high | low | max. | max. | max. | max. | max. | high | low | max. | ||
0.6 | 2.5 | 0 | -5 | 5 | 4 | 3 | 4 | 7 | 7 | 0 | -40 | -250 | 5 |
2.5 | 10 | 0 | -5 | 5 | 4 | 3 | 4 | 7 | 7 | 0 | -40 | -250 | 5 |
10 | 18 | 0 | -5 | 5 | 4 | 3 | 4 | 7 | 7 | 0 | -80 | -250 | 5 |
18 | 30 | 0 | -6 | 6 | 5 | 3 | 4 | 8 | 8 | 0 | -120 | -250 | 5 |
30 | 50 | 0 | -8 | 8 | 6 | 4 | 5 | 8 | 8 | 0 | -120 | -250 | 5 |
Note:1)Including 0.6.
2)Diameter series 7 and 8,no regular cost.
3)Only suitable for groove type ball bearing.
4)Indicating the single linternal ring of the bearing to be uesd in pair or group duing installation.
Table 6 Out Ring of 5 Grade Telerance
D mm | Δdmp | Vdp | Vdmp | Kea | SD SD | Sea | Seal | ΔCs ΔCis | VCs VCis | ||||
Diameter Series | |||||||||||||
9 | 0,1,2,3,4 | ||||||||||||
over | incl. | high | low | max. | max. | max. | max. | max. | max. | high | low | max. | |
2.5 | 6 | 0 | -5 | 5 | 4 | 3 | 5 | 8 | 8 | 11 | Identical to ΔBs and VBs of inner ring of same bearing | 5 | |
6 | 18 | 0 | -5 | 5 | 4 | 3 | 5 | 8 | 8 | 11 | 5 | ||
18 | 30 | 0 | -6 | 6 | 5 | 3 | 6 | 8 | 8 | 11 | 5 | ||
30 | 50 | 0 | -7 | 7 | 5 | 4 | 7 | 8 | 8 | 11 | 5 | ||
50 | 80 | 0 | -9 | 9 | 7 | 5 | 8 | 8 | 10 | 14 | 6 |
Note:
1)Including 2.5.
2)Diameter series 7 and 8,no regular cost.
3)Diameter series 9、0 and 8,no regular cost.
4)UNsuitable for the outside Flange of the bearing.
5)Only suitable for groove type ball bearing.